Procom EDP200T2-O Specifications

This appliance may be installed in an aftermarket, permanently located, manufactured(mobile) home, where not prohibited by local codes. This appliance

10Ventilation Air From OutdoorsProvide extra fresh air by using ventilation grills or duct. You must provide two permanent openings: one within 12 inc

11Fig. 4 - Minimum Clearance to Wall and CeilingINSTALLATION NOTICE: This heater is intended for use as supplemental heat. Use this heater along with

12CONNECTING TO GAS SUPPLY WARNING: A qualied technician must connect heater to gas supply. Follow all local codes. WARNING: This appliance requires

13 CAUTION: Use only new black iron or steel pipe. Internally tinned copper tubing may be used in certain areas. Check your local codes. Use pipe of ½

14CAUTION: Two gas line installations at the same time are prohibited. The access plate to the simple switching means shall not be opened while the he

15CHECKING GAS CONNECTIONS WARNING: Test all gas piping and connections for leaks after installing or servicing. Correct all leaks immediately. WARNI

16INSTALLING LOGS Fig. 14 - Installing Log SetIMPORTANT: Make sure log does not cover any burner ports (see Fig. 14). It is very important to install

17OPERATION FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a re or explosion may result causing pr

18THERMOSTATIC CONTROL OPERATIONThe thermostatic control used on this model differs from standard thermostats. Standard thermostats simply turn the bu

19INSPECTING BURNERSCheck pilot ame pattern and burner ame patterns often. PILOT FLAME PATTERN 1. Turn control knob to pilot position2. Inspect pilo

2 TABLE OF CONTENTS Important Safety Information...

20CARE AND MAINTENANCE CLEANING BURNER INJECTOR HOLDER AND PILOT AIR INLET HOLEWe recommend that you clean the unit every three months or after 2500 h

21TROUBLESHOOTING WARNING: If you smell gas: • Shut off gas supply. • Do not try to light any appliance. • Do not touch any electrical switch; do n

22Problem Possible Cause Corrective ActionBurner backring during combustion.1. Burner orice is clogged or damaged.2. Burner is damaged.3. Gas regula

23REPLACEMENT PARTS NOTE: Use only original replacement parts. This will protect your warranty coverage for parts replaced under warranty.PARTS UNDER

24REPLACEMENT PARTS LIST Part. Description Part # QTY1 Burner Assembly PSD20T230 12 DF ODS NDD0308-400 13 T-Stat Valve Assembly SIT545-200 14 Piezo I

25REPLACEMENT PARTS LIST This list contains replaceable parts used in your heater. When ordering parts, follow the instructions listed under Replaceme

26

27CORNER MANTEL TRIMCAUTION: If baseboards are installed where the replace is intended to be displayed, then the replace will not t ush against th

28ASSEMBLY INSTRUCTIONS1. Turn the replace top panel over. Using the connector brackets that are supplied, connect the replace top panel

29Fig. 33. Drill two holes (5/16 in.) in the corner where the replace is to be displayed. Drill the rst hole 34 5/16 in. from the ground

3MODEL EDP200T2-JA & EDP200T2-MOInput Max. 20,000 BTU/Hr 19,000 BTU/HrInput Min. 11,500 BTU/Hr 16,500 BTU/HrGas Type Natural LP/Pr

30WARRANTY INFORMATIONKeep This WarrantyIMPORTANT: We urge you to ll your warranty registration card within TEN(10) days of date of installation, com

4IMPORTANT SAFETY INFORMATIONIMPORTANT: Read this owner’s manual carefully and completely before trying to assemble, operate, or service this heater.

510. Operating heater above elevations of 4,500 feet could cause pilot outage.11. To prevent performance problems, do not use propane/LP fuel

6SAFETY PILOTThis heater has a pilot with an Oxygen Depletion Sensing (ODS) safety shutoff system. The ODS/pilot shuts off the heater if there is not

7PRODUCT IDENTIFICATIONWATER VAPOR: A BY-PRODUCT OF UNVENTED ROOM HEATERSWater vapor is a by-product of gas combustion. An unvented room heater produc

8AIR FOR COMBUSTION AND VENTILATION WARNING: If the area in which the heater may be operated does not meet the required volume for indoor combustion a

9DETERMINING FRESH-AIR FLOW FOR HEATER LOCATIONDetermining if You Have a Conned or Unconned SpaceUse this worksheet to determine if you have a conn